MACHINERY & EQUIPMENT

Machinery EAC Compliance

Identify regulatory scope from machinery's intended use, construction and risks first. Commercial names alone do not determine machinery safety regulation applicability.

Verify regulations, applicants, assessment form, materials and procedures against product facts, destination and current official requirements. This page outlines services, not a specific compliance conclusion or a promise of results or completion times.

SERVICE OVERVIEW

What Problems Does This Service Address?

ТР ТС 010/2011 on machinery and equipment safety covers machinery and equipment listed in its scope provisions, subject to exclusions and special rules. Some equipment may also involve low voltage, EMC, pressure equipment or explosive atmosphere regulations.

WHO MAY NEED IT

Which Businesses Should Explore This?

Manufacturers, exporters, importers and local operators planning to sell relevant products in EAEU member states.

SCOPE & APPROACH

Topics Usually Reviewed in Discussions

Identify information gaps first, then confirm preparation and responsibilities.

01

Initial Scope Screening

ТР ТС 010/2011 on machinery and equipment safety covers machinery and equipment listed in its scope provisions, subject to exclusions and special rules. Some equipment may also involve low voltage, EMC, pressure equipment or explosive atmosphere regulations.

02

Assessment Pathway

ТР ТС 010/2011 provides declaration of conformity, mandatory certification and other assessment pathways for covered products, determined by regulatory annexes, product category and schemes. Do not categorise all machinery under either certificates or declarations alone.

03

Applicant

Applicants must be legal persons or individual entrepreneurs legally registered in a Member State and meet the relevant regulation's manufacturer, seller or manufacturer's authorised representative requirements.

04

Assessment Entities and Responsibilities

The Eurasian Economic Commission establishes Union technical regulations. Certification bodies, laboratories and Member State applicants prescribed by law complete specific assessments under applicable schemes.

05

Points to Confirm

Confirm product coverage and exclusions, serial/batch/single-unit supply, assessment schemes, production control and validity rules.

06

Technical Documentation Areas

Typically check product descriptions and models, risk assessment, design/technical documents, instructions, standards, test records, manufacturer and applicant information. The final list depends on regulation and scheme.

07

Procedure

Identify product and screen regulations → determine applicant and assessment scheme → organise technical documentation and samples/testing → qualified parties assess and issue or register documents as required → verify registration, marking and ongoing duties.

08

Marking and Labeling

Affix EAC marking and required product information only where required by applicable regulations and after meeting assessment and market placement conditions. The marking is not a standalone licence.

09

Applicability Boundaries

This is regulatory navigation, not a product-specific applicability conclusion. Pressure, gas, explosive atmosphere, lifting and other special machinery require separate identification of specific regulations.

10

Service Content

Check product use, construction, models and manufacturer records to identify potentially applicable regulations

11

Service Content

Review assessment form, applicant and document list under specific regulations

12

Service Content

Assist with technical documentation and communication with Member State applicants and assessment bodies

GET READY

Suggested Materials Before Contacting Us

Describe the product and current progress even if documents are incomplete, then supplement later.

  • Accurate name, use, models/specifications, technical parameters and photographs.
  • Manufacturer, production address, origin and company details.
  • Instructions, technical documents, drawings/construction and risk/safety materials as relevant.
  • Existing tests, certificates/declarations, draft labels and planned sales countries.
  • Local applicant/representative and authorization details where required.
HOW TO START

From Initial Assessment to Confirmed Engagement

STEP 01

Submit Product and Market Information

Describe name, use, models, manufacturer and target member states.

STEP 02

Review Regulations and Application Conditions

Confirm system, assessment form, applicant and evidence against product characteristics.

STEP 03

Confirm Documentation and Scope

Organize materials, tests/audits, responsibilities, estimated timing and fees.

STEP 04

Cooperate as Agreed and Verify Documents

Follow confirmed assessment procedures and verify scope, holder, validity and territory afterward.

Verify regulations, applicants, assessment form, materials and procedures against product facts, destination and current official requirements. This page outlines services, not a specific compliance conclusion or a promise of results or completion times.

OFFICIAL SOURCES

Official Sources and Applicability Boundaries

Check current versions, scope and publication dates of official documents.

START WITH YOUR PRODUCT

Check Product Details Before Confirming Arrangements

Provide product name, use, manufacturer, destination and existing documents to discuss pathways and scope.